Cable Pulling Machine Cable Conveyer
Product introduction
Cable Conveyer is suitable for urban power network reconstruction and new laying of cables, especially suitable for long distance cable release, reducing labor intensity, and also improving the quality of the project.
The thrust of the Cable Conveyer is large, small size, easy to be put the construction of the well, and its weight is light.
The Cable Conveyer can be pushed by single machine, and also can be connected in series with a machine, and the synchronization of several machines is controlled by a control box.
The conveyor wheel is made of rubber die casting, which will not damage the cable sheath, and adjust the center distance according to the external diameter of the cable. 380V motor or gasoline engine is used for power of cable conveyor.
wire rope PULLING WINCH TECHNICAL PARAMETERS
|
Item number |
Model |
Motor Power （KW） |
Clamping force (KN) |
Pull Force （KN） |
Conveying speed （m/min） |
Outline size （mm） |
Diameter of cable （mm） |
Supply Voltage （V） |
Weight （kg） |
|
21103 |
DCS-5 |
1.1*2 |
≤2.7 |
7 |
7 |
950*500*400 |
30-150 |
380 |
150 |
|
21105 |
DCS-8B |
1.5*2 |
≤2.7 |
9 |
7 |
1000*530*400 |
30-200 |
380 |
195 |
|
21102 |
DCS-110 |
4 |
≤2.7 |
6 |
7 |
1050*530*550 |
30-180 |
GX160 |
190 |
Related products
-
Stringing Block Special Block press rising wire...
Product introduction When paying off in high mountains and mountains, the height difference between iron towers is large, so it is very easy for the traction rope, conductor or ground wire to slip out of the paying off pulley groove when it is rised. The pressing pulley is mainly used to press the rising traction rope, conductor or ground wire during paying off. When it is applicable to wire rope or steel strand, the pulley is made of steel wheel. When applicable to...
-
Belt Driven Gasoline Diesel Electric Engine Tra...
Product introduction Power Winch for Lifting is used in power transmission and distribution engineering, telephone construction tower erection, traction cable, line, hoisting tools, tower erection, pole setting, stringing wire in electrical power line construction. The power winch is driven by a belt, effectively prevent the damage of overload. Different gears correspond to different speeds, anti reverse gear moment to ensure construction safety. According to the po...
-
MANUAL LIFT PULLER HAND WINCHES LIFTING HANDLE...
Product introduction 1. Wire rope pulling hoist is a new type of high-efficiency, safe and durable lifting machinery with three functions of lifting, pulling and tensioning. 2.The structure of the whole machine is reasonable in design，with safety self-locking device, high in safety factor and long in service life. 3. The casing is made of aluminum alloy, which is light and easy to carry and use. 4. The main rated lifting capacity is 8KN, 16KN, 32KN and 54KN. Stan...
-
822mm Wheels Sheaves Conductor Pulley Stringing...
Product introduction This 822mm Large Diameter Stringing Block possesses the dimension (outside diameter × groove bottom diameter × sheave width) of Φ822 × Φ710 × 110 (mm). Under normal circumstances，its maximum suitable conductor is ACSR630, which means that the aluminum of our conducting wire has the maximum cross section of 630 square millimeters. The maximum diameter through which the sheave passes is 85mm. Under normal circumstances, the model of the maximum Sp...
-
Cable Roller Nylon Aluminum Steel Sheave Ground...
Product introduction Cable rollers should always be used when pulling cables. Straight cable runs are pulled in using straight cable rollers suitably placed in the ground, avoid damaging cable surface sheath by friction between cable and ground. Straight cable runs are pulled in using straight cable rollers suitably placed in the cable trench to prevent the cable being dragged on the trench bottom or in mud. Cable roller spacing is dependent on cable type being laid ...
-
Triple Wheels Neoprene Lined Aluminum Sheaves C...
Product introduction Aluminum Sheaves Coated Rubber Stringing Block, the aluminum sheave or the nylon sheave used as the base material, and the sheave groove is coated with rubber. Before coating, the groove surface of the aluminum sheave or the nylon sheave needs to be specially processed, Then the high temperature rubber pressing process is adopted, so that the rubber layer can be firmly adhered to the aluminum sheave or the nylon sheave. The purpose of aluminum sh...